BX60 Stuffer Mixer is meticulously developed by absorption of all good characteristics of existed Stuffer Mixer on the home and abroad marke

1. Introduction
YBX60 Stuffer Mixer is meticulously developed by absorption of all good characteristics of existed Stuffer Mixer on the home and abroad market. It is applicable to blend materials for canteens, restaurants, hotels and other food processing factories. It also can be used to blending materials in pharmaceutical factory, raw materials factory of chemical industry and so on.

2.Structure Feature and Working Principle
2.1Structural feature is showed in the following diagram of stuffer mixer.

The Structure Diagram of YBX60 Stuffer Mixer
1.The stuffer mixer is consisted of rack, transmission part, hopper, stirrer and the part of electrical control etc.
2 Chain drive transmission ensures the machine runs stably with low noise. All the parts which contact with the blended materials are made of stainless steel. It conforms national food safety standards.
. Working principle
After putting the mixture into the hopper, start the machine. The stirrer will rotate normal and reverse in the hopper to mix the materials evenly. Then turn the hopper by 90 degrees and you can take out the well blended mixture.

3.Technical Parameter
a. Rated input power: 1.5kW b. Motor power: 1.1kW
c. Rated Voltage: ～ 220V d. Rated Frequency: 50 Hz
e. Throughout: the largest amount of mix stuffing is 60L
f. Stirrer speed: 78r/min g. Waterproof ratings: IPX1
h. Weight: 135kg i. Dimensions: 775×500×910 mm

4.Operation and Usage
4.1 Preparation and examination before using
4.1.1 Install the machine on the working position. Lock the wheels by the brakes to make the machine work steadily.
4.1.2 Make sure that the supplied voltage is coincided with the permit voltage of the machine.
4.1.3 Extend the length of power cord. Make sure the wire which marked as ground wire is earthed reliably. The other wires should be correctly connected to the leading-out terminal of the matched circuit breaker which is provided by customer self. It is important to connect the wires with the equipotential mark reliably. After that, plug in and switch on the button of normal or revere rotation. If the machine can run smoothly and has no abnormal sound, you can begin your work.
▲ Do not put your hand or other foreign material into the hopper when the machine is running to avoid danger.
4.2 Operation and Usage
4.2.1 Make sure there are no other foreign material in the hopper, the turning of the hopper is flexible, and the positioner of the hopper is fixed reliably.
4.2.2 Put the materials into the hopper and then switch on the normal or reverse rotation button, and then. Open the top cap and the stirrer will stop running automatically when you examine the materials is mixed uniformly or not. Unplug the positioner of the hopper and turn the hopper by 90 degrees, you can take out the mixture from the hopper.
Warning: This machine is strictly prohibited from using to mix the flour or overhigh viscosity materials to avoid machine damage.

5.Fault Analysis and Resolution

6.Maintenance
Any repair or maintenance work must be done while the machine power is turned off.
If the speed or efficiency of the machine is declined, you should take the right shield down and check the elasticity and abrasion of the common V-belt. And adjust or replace the belts in time.
After using the machine, clean it carefully to ensure the dietetic hygiene. Do not wash the machine by water spray tube directly. The stirrer can be taken out of the hopper to clean the stirrer and hopper completely.
Inject proper calcium-based grease from the oil filler periodically.
The method of stirrer teardown:
There is a "0" symbol on the fixed shaft and the left flange. While disassembling, rotate the fixed shaft firstly and make alignment of "0" symbol between the fixed shaft and the left flange. After that, one hand hold the stirrer to prevent the stirrer damaging the hopper when the fixed shaft was extracted; the other hand grasp the fixed shaft and pump it out, then the stirrer can be easily took out. The installing sequence is opposite with that of the disassembly.
If you hear abnormal sound when the machine is working, you must stop the machine immediately and don’t use it until the trouble is gotten rid of.

7.Electrical principle chart and list of electrical components

NO. Code Name Technical Parameter Amount remarks
1 M Motor YL90S-4 1.1kW 1
2 SB1-SB3 Button LA19-11 3 1red and 2green
3 KM1-KM2 AC contactor CJ20-10A 220V 2
4 HL Indicator ND11-11 1

8.Transportation and Storage
8.1 Forbid bumping, deflection and inversion during working to avoid machine from damaging which may have an effect on using.
8.2 Store the machine in a dry, noncorrosive environment during long time disuse. Don’t contacts with the corrosive to avoid machine damaged.